Cycling Gear and Cadence Planner

Compare bicycle gearing with converted wheel circumference and an entered cadence.

On-device No sign-up Free to use

Compare cycling gears controls

?

The teeth on each front chainring, separated by commas. Up to 6 chainrings, each a whole number from 10 to 80.

?

The teeth on each rear sprocket, separated by commas. Up to 14 sprockets, each a whole number from 8 to 60.

?

The distance the wheel travels in one full turn, for the wheel and tyre you actually use. Measure it, or take it from your tyre size chart. This is the figure the speed maths uses.

?

The unit your circumference is written in.

?

Your pedalling cadence, a whole number from 20 to 200 revolutions per minute. The speed table uses the single value you enter.

Drop your file here

or choose one from your device

Choose a cycling-gear-cadence-planner.json file saved by this tool to load its settings back into the form.

    Processed in your browser. Your inputs stay on this device.

    Showing an example. Change the fields, then use compare cycling gears to update it.

    Result

    Showing an example.

    Compare two front chainrings with eight rear sprockets at 90 rpm and 2,136 mm wheel circumference. The 50/11 combination gives a theoretical 52.429 km/h; this is mechanical arithmetic, not a riding-speed forecast.

    Built 16 gears from 2 chainrings and 8 sprockets at 90 rpm.

    Loading the tool. Your result will appear here.

    https://usefreetools.net/cycling-gear-cadence-planner · 20 November 2026

    Was this helpful?

    How to use Cycling Gear and Cadence Planner

    1. Enter the front chainring and rear sprocket tooth counts, separated by commas. The result removes duplicates and sorts each list before building every front/rear combination.
    2. Enter wheel circumference, not diameter: this is the distance traveled in one wheel turn. Choose mm, cm, m or inches to match the measurement.
    3. Enter one cadence in crank revolutions per minute and select Compare cycling gears. Review gear ratio, development in meters per crank turn and speed in km/h.
    4. Change cadence to compare another rate. Circumference unit changes carry the physical measurement across; the calculation and saved project retain its original amount/unit until you edit it.
    5. Download cycling-gear-cadence-planner.csv or its PDF for the matrix. Keep the JSON project to restore the tooth lists, circumference and cadence later.

    Example: Cycling Gear and Cadence Planner

    Compare two front chainrings with eight rear sprockets at 90 rpm and 2,136 mm wheel circumference. The 50/11 combination gives a theoretical 52.429 km/h; this is mechanical arithmetic, not a riding-speed forecast.

    You add
    Front chainring teeth: 50, 34; Rear sprocket teeth: 11, 13, 15, 17, 19, 21, 24, 28; Measured wheel circumference: 2136; Circumference unit: mm; Cadence in revolutions per minute: 90
    You get
    Built 16 gears from 2 chainrings and 8 sprockets at 90 rpm.

    Options

    Circumference
    The form asks for distance travelled in one wheel revolution, rather than diameter. Units are mm, cm, m or in.
    Gear and cadence inputs
    Use up to 6 front chainrings and 14 rear sprockets. One cadence from 20–200 rpm applies to the matrix; revise it to compare another cadence.

    Supported inputs and limits

    • Supply 1 to 6 front counts from 10 to 80 teeth and 1 to 14 rear counts from 8 to 60.
    • Counts and cadence must be whole numbers; cadence ranges from 20 to 200 rpm.
    • The wheel measurement must be positive, at most 100,000 of its selected unit, with up to 12 decimal places.
    • These are parser bounds, not equipment recommendations.
    • Circumference conversions display up to 12 decimal places while preserving the original measured value for calculation and project export until edited.
    More details

    Fastest and slowest combinations are chosen before display rounding, even when close printed speeds look alike.

    The matrix does not check gear compatibility, chain line, slip, resistance, power, terrain, effort or bike fit.

    There are no tire-size presets or gear-inch output.

    Processing is local without automatic saving;

    JSON imports from this tool are limited to 512 KiB.

    PDF text uses the supported standard-font character set.

    Where your input is processed

    This tool does not upload your inputs. See the limits for anything saved on your device.

    The drivetrain calculation is mechanical

    Wheel travel per crank revolution is wheel circumference multiplied by front teeth divided by rear teeth. Cadence turns that travel into a theoretical speed. A measured circumference can reflect the actual wheel better than a nominal tyre size. The calculation ignores slip, effort, gradients and aerodynamics.

    Questions about Cycling Gear and Cadence Planner

    Does it estimate the effort needed?

    No. The output is mechanical travel and theoretical speed, without a power or terrain model.

    Which wheel size should I use?

    Use the circumference requested by the form, preferably measured for the wheel. It is not a bike-fit recommendation.

    Can I compare several sprockets?

    Yes, within the stated bounds. The matrix compares the entered front and rear combinations at the supplied cadence.

    Page updated · Project managed by Tony Hines · Report a problem with Cycling Gear and Cadence Planner