Audio Volume Booster and Normalizer

Adjust audio gain, sample peaks or measured integrated loudness with explicit clipping limits.

On-device No sign-up Free to use

Adjust audio volume controls

  1. 1 Add files
  2. 2 Arrange/Options
  3. 3 Download

Drop your file here

or choose one from your device

Supported PCM WAV or browser-decodable MP3, M4A, Ogg, WebM, FLAC or AAC. Selected files together: 128 MiB, 600 seconds and 256 MiB decoded samples. PCM WAV retains its rate/channels; other formats decode at 48 kHz and retain mono/stereo channels. Metadata is not copied. Decoder support varies and decoding may use more memory than the compressed size.

    ?

    For sample-peak normalization. This does not measure LUFS, perceived loudness or peaks between samples.

    ?

    For gain mode. Positive gain is capped when necessary to keep sample values within the PCM range.

    ?

    For loudness matching. Enter a plain number such as -16, -14 or -9 LUFS. Needs a 48 kHz recording, because this mode does not resample, and takes longer than the peak modes.

    ?

    For loudness matching. The one-pass gain stops here so the sample peak stays under the ceiling. This is not a true-peak limiter.

    ?

    MP3 files are much smaller and play everywhere. WAV keeps every sample without compression.

    ?

    Constant bitrate. Higher numbers sound closer to the source and make larger files.

    Result

    Showing an example.

    Set a known sample peak without measuring loudness.

    The peak becomes approximately 0.89125 before PCM16 quantization, using a gain of about 1.78250. The report identifies the applied gain.

    Loading the tool. Your result will appear here.

    https://usefreetools.net/audio-volume-normalizer · 20 November 2026

    Was this helpful?

    How to use Audio Volume Booster and Normalizer

    1. Load supported audio and choose sample-peak normalization, gain adjustment or integrated loudness matching.
    2. Set the relevant target or gain. Loudness matching needs 48 kHz audio and a numeric LUFS target plus sample-peak ceiling.
    3. Run the adjustment and review the reported applied gain and clipping cap.
    4. Listen to the download at a safe playback volume before comparing it with the source.

    Example: Audio Volume Booster and Normalizer

    Set a known sample peak without measuring loudness.

    You add
    Source: a mono WAV whose maximum absolute sample is 0.5. Volume adjustment: Normalize sample peak; Target sample peak: -1 dBFS; Requested gain: 0. Save as: WAV.
    You get
    The peak becomes approximately 0.89125 before PCM16 quantization, using a gain of about 1.78250. The report identifies the applied gain.

    Options

    Integrated loudness target and sample-peak ceiling
    Enter a numeric LUFS target, such as -16, -14 or -9. The tool applies one bounded gain to both channels and reports the measured result. Its sample-peak ceiling can reduce the requested gain; it does not certify a streaming platform's rules or guarantee true-peak headroom.
    Volume adjustment
    Normalize scales the observed peak toward a target. Gain mode applies an entered change in dB. Loudness mode uses a measured numeric LUFS target at 48 kHz. Each mode retains its clipping limits.
    Target sample peak (dBFS)
    Zero dBFS reaches the full sample range. A negative target leaves sample headroom; it does not certify headroom for reconstructed true peaks.
    Requested gain (dB)
    Positive values request amplification; negative values reduce level. The result reports when clipping prevention lowers the requested increase.
    Save as
    MP3 saves the adjusted recording as a much smaller file that plays everywhere. WAV keeps uncompressed PCM16 samples. MP3 is selected when the page loads.
    MP3 quality
    Constant bitrate for the adjusted recording: 128, 192, 256 or 320 kbps, encoded with LAME in your browser. 192 kbps is selected when the page loads. Hidden when WAV is chosen.

    Supported inputs and limits

    • Supported PCM/float32 WAV retains mono/stereo at 8–96 kHz.
    • Browser-decodable MP3, M4A, Ogg, WebM, FLAC and AAC decode at 48 kHz; support varies.
    • Input: 128 MiB, 600 seconds and 256 MiB decoded samples.
    • Export is MP3 (128 to 320 kbps) or PCM16 WAV, without metadata.
    • MP3 encoding can move the measured peak slightly.
    More details

    Loudness matching uses the existing gated measurement at 48 kHz and needs at least 400 ms of measurable audio; other rates are refused without resampling.

    One-pass gain is capped at ±30 dB and by the sample-peak ceiling, so a LUFS target may not be reached.

    This is not a true-peak limiter or platform certification.

    Silence may have no measurable loudness.

    Native decode cannot stop immediately.

    Where your input is processed

    This tool does not upload your inputs. See the limits for anything saved on your device.

    Peak and loudness answer different questions

    Sample peak is the largest stored sample magnitude. Two files with the same peak can sound different. Loudness mode measures the supported 48 kHz recording with the existing gated meter, requests target minus measured LUFS as gain, then measures the adjusted samples again. The sample-peak ceiling and one-pass gain cap may prevent reaching the target; both requested and achieved values are reported. PCM16 quantization can move the downloaded file's measurement slightly.

    The clipping cap can reduce a requested boost

    Gain mode caps an increase when the input peak would exceed the sample range. The applied gain can therefore be smaller than the value you entered. Silence has no peak to raise through normalization. Output uses 16-bit PCM and omits original tags, so retain a higher-precision source when subsequent editing is planned.

    Questions about Audio Volume Booster and Normalizer

    Is sample peak the same as perceived loudness?

    No. Loudness also depends on content, duration and frequency.

    Does this measure inter-sample true peaks?

    Peak and gain modes use stored sample values. Loudness mode also reports the existing meter's true-peak estimate, but its gain ceiling controls sample peak and is not a true-peak limiter.

    What happens when requested gain would clip?

    The page reports the applied gain and its clipping-prevention adjustment rather than silently clipping samples.

    Can I save the result as MP3?

    Yes. MP3 is the default. MP3 encoding can move peaks by a fraction of a dB, so choose WAV when exact levels matter.

    Page updated · Project managed by Tony Hines · Report a problem with Audio Volume Booster and Normalizer