Packaging Dieline Generator

Draw an open-tray or rectangular-carton paper net with separate cut and fold lines, then export SVG and a full-size PDF.

On-device No sign-up Free to use

Draw dieline controls

?

Only these two flat layouts are generated. Both are reviewed patterns, not tested assemblies.

?

Wall depth for a tray; side height for a carton.

?

Added to base length, base width and wall depth/height in the flat geometry. Use 0 for a paper test fit; actual folding clearance must be checked.

?

The net must fit the sheet with a margin; an oversized net is refused.

?

Panel names, dimensions and the 100 mm calibration line.

Processed in your browser. Your inputs stay on this device.

Showing an example. Change the fields, then use draw dieline to update it.

Result

Showing an example.

Draw the 120-by-90 mm open tray with 40 mm walls and a 0.4 mm allowance. Its flat net spans 201.2 by 171.2 mm and fits the selected A3 sheet.

Built a tray net with 16 cut and 12 fold segments on 201.2 × 171.2 mm.

Loading the tool. Your result will appear here.

https://usefreetools.net/packaging-dieline-generator · 20 November 2026

Was this helpful?

How to use Packaging Dieline Generator

  1. Choose Open tray with corner glue tabs or Rectangular carton with tuck flaps. Enter base length, base width and wall depth or carton height in millimeters.
  2. Set Material allowance from 0 to 2 mm. It is added to each base dimension and the wall depth/height; it is not a measured prediction of your material’s folding clearance. Use 0 for a paper trial.
  3. Choose A4 or A3. The tool tries a sheet orientation that fits the net within the reserved margins and refuses a net that fits neither orientation.
  4. Leave Print panel and fold labels on to include panel text and the 100 mm calibration line. Turning it off removes that line as well as the labels.
  5. Inspect the flat drawing. Solid dark lines are cuts; dashed blue lines are folds. Download dieline-tray.svg/PDF or dieline-carton.svg/PDF for the chosen family.
  6. Print at Actual size or 100%, measure the calibration line when included, then cut and assemble a paper sample before using thicker stock.

Example: Packaging Dieline Generator

Draw the 120-by-90 mm open tray with 40 mm walls and a 0.4 mm allowance. Its flat net spans 201.2 by 171.2 mm and fits the selected A3 sheet.

You add
Box family: tray Base length (mm): 120 Base width (mm): 90 Depth or height (mm): 40 Material allowance (mm): 0.4 Sheet size: a3 Print panel and fold labels: on
You get
Built a tray net with 16 cut and 12 fold segments on 201.2 × 171.2 mm.

Options

Entered and cut dimensions
Allowance is added once to base length, base width and wall depth/height in the flat geometry. It does not account for bend radius, grain, adhesive or a measured inside finished size.
Cuts, folds and calibration
Cut solid lines and fold dashed lines. The label switch controls both panel labels and the 100 mm calibration line. A small panel may have its label omitted to avoid text that will not fit.

Supported inputs and limits

  • Two flat pattern families only: open tray and rectangular carton with tuck flaps.
  • Base length and width each range from 20 to 600 mm, depth/height from 10 to 400 mm and allowance from 0 to 2 mm, with at most one decimal place.
  • The complete net must fit A4 or A3 within reserved margins.
  • The PDF is drawn at full scale on the selected sheet; printer scaling is outside the tool.
  • The SVG canvas is sized around the net rather than being the same A4/A3 page.
More details

Calibration is absent when labels are off.

Geometry checks do not establish manufacturing tolerances, load capacity, food suitability or closure in your material.

Test-fit the paper layout first.

Where your input is processed

This tool does not upload your inputs. See the limits for anything saved on your device.

Check a paper sample before using thicker material

Material thickness, fold behavior, adhesive and printer scaling affect the assembled result. The allowance changes the flat geometry by a simple entered amount; it does not calibrate a manufacturing process. Keep labels on for the calibration line, print at actual size, measure it and assemble a paper sample before committing other material.

Questions about Packaging Dieline Generator

Are the values millimeters?

Yes. Use the declared millimeter dimensions consistently.

Should I cut every line?

No. Follow the separate cut, fold and tab legend.

Is it ready for commercial manufacturing?

It is a paper-project pattern; material and process tolerances need separate review.

Page updated · Project managed by Tony Hines · Report a problem with Packaging Dieline Generator